How to glue wallpaper in the corners: instructions, sticking the outer, inner corner, docking

The article can find the answer to the question of how to glue wallpaper in the corners. It is necessary to treat the process of finishing with full responsibility, irregularities can catch the eye, thereby spoiling the impression of the newly made repair.

Step-by-step instructions for pasting inside corners

When finishing the main problem can be uneven walls and the resulting folds on the wallpaper. It is also necessary to take into account that with curved walls, the joints of wallpaper can diverge.

1. After gluing the latter in front of the inner corner of the canvas, it is necessary to measure the remaining distance. It is measured from the edge of the glued sheet to the adjacent wall, 10-15 millimeters are added to the resulting figure. If the walls are severely curved, then the additional figure may be larger.

   

2. The band is cut equal to the resulting figure, taking into account the allowance.
3. Glue treated surfaces. Depending on the type of coating, it can only be a wall or both surfaces.
4. The strip is glued by its own cut side to the wall. Wallpaper should go to another plane.

   

5. If the pasted wallpaper is wrinkled, you need to make several small cuts perpendicular to the folds.
6. Level or slope on the adjacent wall is a vertical line. The distance from the corner is equal to the width of the previous cut strip, without taking into account the additives.
7. Surfaces are coated with glue, after which the coating is glued to the wall with a flat side to the marked line. The cut off side extends onto the adjacent wall.

   

8. If the coating is thick, then the wallpaper is cut off along the overlay line.

How to glue the outer corner (outer)?

The protruding angle should be glued in by analogy with the internal one, however there are some minor differences that also need to be taken into account when working.

1. The distance from the pasted wallpaper to the adjacent wall is measured. To the resulting figure is added 20-25 millimeters.
2. The segment is cut, taking into account the added 20-25 millimeters.
3. Before gluing surfaces are treated with an adhesive.
4. The smooth edge needs to be glued to the wallpaper already fixed on the wall, the hand cut off by itself “comes in” on the adjacent plane.

   

5. If necessary, small cuts are made in the place of wallpaper setting onto another wall, smoothed and pressed against the wall.
6. A vertical strip is drawn on the adjacent wall at the distance of the newly pasted cut strip plus 6-10 millimeters.
7. After applying the adhesive, the strip is applied to the wall with an even side to the marked line, going to the edge of the already pasted strip.

   

8. Joints are coated with glue and ironed with a roller. After that, the top layer is cut by a ruler and two layers are joined together.

   

What if the corners are uneven?

Uneven walls are a frequent problem of old houses. Before you begin to glue the finish coating, it is advisable to carry out the preparatory work and bring the surface "in order." If the corners are visually even and do not require major repairs, it will be enough to walk with a hard cloth, removing small irregularities and dust. If the irregularities are noticeable to the naked eye, it is better to do a little work before you begin to glue the wallpaper.

1. When working on the finishing putty, a plastic corner is inserted and fixed with a putty mixture. They can be purchased at the hardware store.

   

2. After drying, the surface is leveled with a putty or plaster.

   

3. After drying, the walls are treated with a primer.
4. After the work done on the walls, you can glue the finish.

Features sticky meter wallpaper

Wide canvases are convenient because they allow you to finish with a smaller number of seams on the surface. Glue them harder, but the result is worth it.

1. Most often meter wallpapers are made with non-woven base and vinyl coating, they are much easier to glue. However, there are also wide paper products.

   

2. When working with non-woven meter-sized products, glue is applied only to the wall.
3. For wide wallpaper requires preliminary preparation of surfaces.
4. For pasting the corners you need to cut the canvas into pieces and glue overlap. Then cut off the excess layer.
5. After applying the strip to the wall for some time, it remains possible to level the coating, gently moving.

How to dock in the corners?

It would seem that such a trifle as glueing the corners in a room can completely spoil all the work if done improperly. And if the wallpaper is also a picture that needs to be customized, then it is worthwhile to approach responsibly to the finish.

1. The strip is glued in such a way that it comes to the adjacent side. The width of the call should not be more than 5 centimeters.

   

2. The angle is leveled with a plastic spatula.

   

3. The next segment is overlapped.
4. In order to cut off the excess overlay evenly, a rule is applied to the middle of the overlap and an extra edge is cut off with a stationery knife. To cut the strip was even worth taking level.

   

How to customize the pattern in the corners?

It is important that the drawing is continuous and even around the perimeter of the room. To do this, you need to properly combine the pattern, and cut off the excess.

1. Stripes also glued overlap. Left allowance for both walls.
2. Plastic spatula wallpaper pressed to the corner.
3. After sticking the second canvas, the wallpaper is cut according to the pattern. This method applies to wallpaper with a small pattern. A large pattern may require trimming along the edges.

Before you glue, you must first prepare the material for the work, spreading the floor covering and studying the pattern. Segments are cut off after picking a pattern in height.

Features of trimming wallpaper in the corners

In order to get a perfectly flat seam in the corner, you need to correctly trim the excess.

1. After the wallpaper is glued to the wall a flat metal ruler is applied, it can also be a spatula or a rule. To the cut line was smooth, you can use the level.
2. A sharp stationery knife cuts off the excess along the edge of the ruler, after which the top layer of wallpaper will move away.
3. Gently poddevaetsya and gets the bottom layer of wallpaper, is removed in the same way.
4. Cloths are coated with glue and tightly pressed to the corner. As a result, for the coating fit snugly together.

To glue wallpaper in the corners is not so difficult, but requires special care and accuracy. Today there is a method of finishing that allows you to perform work without joints at all, namely liquid wallpaper. They are applied in an even layer and do not require such difficulties as the fitting of the pattern, width, accuracy in rounded places and other nuances.